Toupret Ready to Use Patch Repair filler is suitable for gaps, cracks, scratches and holes. Easy to sand, with minimal shrinkage and no need to spot prime. Won't flash or grin. Suitable for interior use, manual applications. It can be applied to any substrates either unpainted or painted: - Gypsum plaster, plasterboard- Old painted surfaces- Cement, concrete, cellular concrete, breeze blocks, bricks and stone Ready to Use Patch Repair can be overcoated with any filler, all types of paints and wall coverings. Specification: Application Thickness: up to 1cmColour: White

Polycell Trade Quick Dry Polyfilla is an instant filler that is suitable for plaster, wood and masonry.It is ideal for small interior jobs and filling hairline cracks. It will not shrink or crack and sands easily.Size: 330g

This EVERBUILD Wet Rot Wood Hardener is a highly penetrative solution of selected resins in solvent which soaks deep into the fibres of decaying wood, and dries to leave the wood hard and resistant to further moisture penetration.The resin-modified wood then becomes an ideal base for repair with EVERBUILD 2 PART HIGH PERFORMANCE WOOD FILLER. The solution is dry in 6 hours, and is suitable for interior and exterior use providing a cost-effective alternative to replacing joinery affected by wet rot.The Hardener binds together damaged wood to form a solid base for filling, and will reduce subsequent water penetration. Specifications: Size: 250 ml.Drying Time: 6 Hours.Flash Point: -17C.

The Everbuild Fill Skim 5 litre Tub is a revolutionary ready-mixed plaster substitute, formulated using lightweight polymer spheres to produce an easy-to-spread, smooth product which enables all tradesmen and DIY enthusiasts to produce a quality finish and is normally only associated with a time served plasterer.This white-coloured Fill Skim dries to a hard, but flexible finish, suitable for wall or ceiling application.It will fill holes down to 25mm in one application and is the ideal choice for covering textured paint surfaces, and for restoring old pitted/uneven plastered walls/ceilings in just one quick application.Fill Skim is the ideal choice for electricians, plumbers, joiners and general builders as a one coat patching plaster for small repair jobs, e.g., over recessed cable trunking and around holes in walls where piping/sockets have been installed.Once dry, Fill Skim will not shrink, sag, or crack and is ready to paint or paper over 24 hours after application. The product finishes smooth and requires little or no sanding, and can be used for internal repairs over plaster, wood, brick, stone, and rendering. Specifications: Colour: White.Size: 5L.

The Everbuild Thermofoam Insulation Foam is a specially formulated, highly flexible PU foam that absorbs component movement thereby giving an air-tight seal to reduce heat loss and improve energy efficiency in buildings. It adheres to all common building materials including concrete, brickwork, wood, plaster, plastic, stone, metal etc. Thermofoam Insulation Foam has been tested to the latest standard and is not only air permeability tested to EN 12114:200-03 but also acoustic rated to EN ISO 717-1 up to 64 dB, temperature resistant (-40 to 80C) and finally fire rated to ISO 13501 Class E. Areas for Use: • Window installation (clean, controlled backfilling and insulated sealing of window and external roller blind cavities) • Gap filling of external door frames (must be used in conjunction with mechanical fixings) • Filling cavities in wall break-through for all types of utilities and services Specification: Colour: Off WhiteSize: 750ml

Everbuild EVBEVFIRE firefoam B1 is a quick setting one-part polyurethane foam with fire retardant properties. The foam expands on application to up to 50 times its original volume and meets the extremely stringent requirements of DIN 4102 Part 1 for Construction Materials; Class B and BS476 Part 20 (1987) where fire ratings of 30 mins to 3.5 hours are achievable. Once cured, the foam can be cut, sawn or plastered over after only one hour. High degree of fire rating: slows down the passage of flames and smoke in comparison to standard B3 grades.Quick setting - can be cut, sawn or plastered in 1-hour is economical in use as it will expand up to 50 times its original volume. Everbuild EVBEVFIRE is gun operated and is ideal for filling:- Gaps around pipe entries through fire rated walls, to provide a fire rated seal around window and door frames, electrical wire chasing prior to plastering, where a fire rating is required, deep joints prior to applying sealant or plaster also irregular gaps in stone, brick, concrete or plaster. Everbuild EVBEVFIRE is ideal for fixing:- door frames, timber structures, windowsills and thresholds and window frames. Also for insulating:- behind cladding to exterior walls, behind sofit and barge boards and even in automotive applications. 750ml

The Everbuild Fire Foam B1 Gun Grade is a quick-setting fire rated, one part polyurethane foam, and expands on application to yield up to 50 times the can contents. Fire rated up to 4 hours in certain joint configurations.For use with an Everbuild Professional Foam Gun, once cured the foam can be cut, sawn or plastered over after only one hour.It will fill irregular and broad gaps where most conventional fillers would fail, and possesses insulating, and sound deadening properties.This Fire Foam meets the stringent requirements of DIN 4102 Part 1 for Construction Materials, Class B1 and BS 476 Part 20. Specification: Size: 750ml.

The Everbuild EVBGFSC5 dual purpose foam cleaner is used to remove wet / uncured foam from brick, PVCu, plaster etc. This EVBGFSC5 simply attaches to Everbuild gun foam applicator for purging through, also includes spray nozzle for use without applicator to remove wet foam from outside of the gun and from most building substrates. Easy to use with some simple steps: Pull the trigger on the gun to release the solvent into the gun barrel and discharge the solvent into a suitable container for disposal. Only stop discharging the cleaner when the solution being ejected from the gun is completely clear. Leave the gun foam cleanse attached to the gun for 5 minutes to allow the solvent in the gun to work on the residues inside. Pull the trigger once again until only clear solvent emerges. Leave for a further 5 minutes and repeat this process 2 or 3 times until the gun is completely clear. 500ml.