Tools

Spill Kit, General Purpose 18 litre

This Scan General Purpose Spill Kit absorbs up to 18 litres of coolant, oil, water, solvents and non-aggressive fluids. Ideal for use in the plumbing trade, for boiler leaks, etc. Contains: 10 x High Performance Absorbent Pads 40 x 50cm2 x High Performance Absorbent Socks 8 x 120cm1 x Disposal Bag with Tie

£ 38.36

MOULD RELEASE Spray 400ml

ROCOL MOULD RELEASE Spray is a high performance PTFE based release agent. Designed to give fast, efficient and clean release with faithful reproduction of the mould profile however complex the mould or minute the detail. Suitable for use on all plastic and rubber mould tools including injection, compression and blow mouldings. Enabling high speed production. MOULD RELEASE Spray offers excellent adhesion, is non-staining, will not transfer to product and can be safely used without fear of blemish or any adverse effect on subsequent finishing operations. Provides a dry matt finish, which is ideal for over painting or printing on, for a gloss finish please see PR Spray. Specification Temperature Range: up to270C

£ 45.31

FLAWFINDER DEVELOPER Spray 400ml

FLAWFINDER DEVELOPER Spray is an aerosol applied white powder. Designed to draw the penetrant out of a flaw, and enhance the definition, to facilitate detection when used in conjunction with FLAWFINDER DYE PENETRANT and FLAWFINDER CLEANER Sprays. Highly absorbent white film for rapid results. Suitable for pressure testing and leak detection

£ 52.52

BSLGH Standard Side Lever Grease Gun

The Lumatic BSLGH Standard Side Lever Grease Gun, complete with air release valve/European pattern bulk filler nipple, 6 inch rigid tube and hydraulic connector. International cartridge loading, accepts a 400cc cartridge. Made in Germany.

£ 28.33

Oil Can Transparent Plastic 350ml

This Faithfull Transparent Oil Can is manufactured from high strength ABS, allowing a clear view of the contents at a glance.The high-pressure trigger action pump is fitted with a flexible spout and a brass nozzle, ideal for lubricating round corners and into tight box sections for precise application of the lubricant. Suitable for use with all kinds of lubricating oil. Specifications: Capacity: 350ml.Nozzle length: 80mm.

£ 5.61

Hydraulic Coupler

This Faithfull Standard Hydraulic Coupler is designed to suit most greasing applications. It is fitted with a spring-loaded ball check mechanism to prevent pressure loss and four fully hardened spring steel jaws for a long service life.The Faithfull Coupler is for use with hand operated grease guns, only with a working pressure of up to 3000psi -207bar. It fits Faithfull grease guns FAI GGHD and FAI GGMP and flexible hoses FAI GGHOSE12 and FAI GGHOSE18.Suitable for use with hand operated grease guns with a 1/8in BSPT thread and working pressure not exceeding 3000psi -207bar.

£ 4.27

Grease Gun Conical Connector

The Faithfull Heavy-Duty Conical Connector is made from high carbon, rust-resistant steel. Its pointed end is used to deflect the ball in the grease nipple, thereby permitting the injection of grease. This connector is ideal for damaged nipples with 1/8in BSP connection and will suit most greasing applications.

£ 3.49

Grease Nipple Selection Box Imperial

The Lumatic Selection Box contains 80 of the most popular metric grease nipples. The fittings are case hardened and plated, ZN3 zinc and clear, head forms conform to DIN 71412. Supplied in a handy clear case with labelled sections for easy identification. Contents: 20 x 1/8in BSP Straight.8 x 1/8in BSP 45 Angle.7 x 1/8in BSP 90 Angle.5 x 1/8in BSP Hook On.5 x 1/4in BSP Straight.6 x 1/4in BSF Straight.10 x 1/4in UNF Straight.5 x 1/4in UNF Straight Long. 7 x 1/4in UNF 45 Angle.7 x 1/4in UNF 90 Angle.

£ 30.02

1066/S Heavy-Duty Side Lever Grease Gun

The Lumatic 1066 Heavy Duty Side Lever Grease Gun is for use with 400g cartridges or 500g bulk fill. It has a permanent spring load design with filler nipple/ air release valve, and ergonomic hand grip for comfort. Supplied with 150mm rigid tube and 4 jaw precision hydraulic connector. Thread: 1/8 BSP.Guaranteed Output: 1.5 cc per stroke.Maximum Pressure: 800 bar (11,600 psi).TUV. DLG and BLT approved.

£ 37.19

All Purpose Silicone Spray 400ml

The EVBSILSPRAY Everbuild All Purpose Silicone Spray (400ml) is a dry silicone lubricant and mould release agent for the easing of friction between two surfaces. It is ideal for use in mould making/release industries, to ease installation of rubber and EPDM gaskets to window and door frames and has hundreds of uses around the home, garage, workshop and industry. It will also enhance the appearance of vinyl and hard surfaces such as car dashboards etc, where the dry-bright finish will eliminate the need to polish. BENEFITS- Enables friction to be reduced between most surfaces.- Eliminates noise and squeak.- Leaves a bright gloss finish to vinyl. AREAS FOR USE- Multitude of uses in the mould making and mould release industries.- Making easy the installation of EPDM gaskets to window and doorframes.- Restoring the black gloss finish to car vinyl trim without the need for polishing.- As a general high quality spray lubricant.

£ 13.59

Ready to Use Patch & Repair 1.5kg

Toupret Ready to Use Patch Repair filler is suitable for gaps, cracks, scratches and holes. Easy to sand, with minimal shrinkage and no need to spot prime. Won't flash or grin. Suitable for interior use, manual applications. It can be applied to any substrates either unpainted or painted: - Gypsum plaster, plasterboard- Old painted surfaces- Cement, concrete, cellular concrete, breeze blocks, bricks and stone Ready to Use Patch Repair can be overcoated with any filler, all types of paints and wall coverings. Specification: Application Thickness: up to 1cmColour: White

£ 8.53

Wet Rot Wood Hardener 250ml

This EVERBUILD Wet Rot Wood Hardener is a highly penetrative solution of selected resins in solvent which soaks deep into the fibres of decaying wood, and dries to leave the wood hard and resistant to further moisture penetration.The resin-modified wood then becomes an ideal base for repair with EVERBUILD 2 PART HIGH PERFORMANCE WOOD FILLER. The solution is dry in 6 hours, and is suitable for interior and exterior use providing a cost-effective alternative to replacing joinery affected by wet rot.The Hardener binds together damaged wood to form a solid base for filling, and will reduce subsequent water penetration. Specifications: Size: 250 ml.Drying Time: 6 Hours.Flash Point: -17C.

£ 22.71

Fill & Skim Tub 5 litre

The Everbuild Fill Skim 5 litre Tub is a revolutionary ready-mixed plaster substitute, formulated using lightweight polymer spheres to produce an easy-to-spread, smooth product which enables all tradesmen and DIY enthusiasts to produce a quality finish and is normally only associated with a time served plasterer.This white-coloured Fill Skim dries to a hard, but flexible finish, suitable for wall or ceiling application.It will fill holes down to 25mm in one application and is the ideal choice for covering textured paint surfaces, and for restoring old pitted/uneven plastered walls/ceilings in just one quick application.Fill Skim is the ideal choice for electricians, plumbers, joiners and general builders as a one coat patching plaster for small repair jobs, e.g., over recessed cable trunking and around holes in walls where piping/sockets have been installed.Once dry, Fill Skim will not shrink, sag, or crack and is ready to paint or paper over 24 hours after application. The product finishes smooth and requires little or no sanding, and can be used for internal repairs over plaster, wood, brick, stone, and rendering. Specifications: Colour: White.Size: 5L.

£ 58.65

Gun Grade Thermofoam® Insulation Foam 750ml

The Everbuild Thermofoam Insulation Foam is a specially formulated, highly flexible PU foam that absorbs component movement thereby giving an air-tight seal to reduce heat loss and improve energy efficiency in buildings. It adheres to all common building materials including concrete, brickwork, wood, plaster, plastic, stone, metal etc. Thermofoam Insulation Foam has been tested to the latest standard and is not only air permeability tested to EN 12114:200-03 but also acoustic rated to EN ISO 717-1 up to 64 dB, temperature resistant (-40 to 80C) and finally fire rated to ISO 13501 Class E. Areas for Use: • Window installation (clean, controlled backfilling and insulated sealing of window and external roller blind cavities) • Gap filling of external door frames (must be used in conjunction with mechanical fixings) • Filling cavities in wall break-through for all types of utilities and services Specification: Colour: Off WhiteSize: 750ml

£ 22.54

Fire Foam B1 Hand Grade Aerosol 750ml

Everbuild EVBEVFIRE firefoam B1 is a quick setting one-part polyurethane foam with fire retardant properties. The foam expands on application to up to 50 times its original volume and meets the extremely stringent requirements of DIN 4102 Part 1 for Construction Materials; Class B and BS476 Part 20 (1987) where fire ratings of 30 mins to 3.5 hours are achievable. Once cured, the foam can be cut, sawn or plastered over after only one hour. High degree of fire rating: slows down the passage of flames and smoke in comparison to standard B3 grades.Quick setting - can be cut, sawn or plastered in 1-hour is economical in use as it will expand up to 50 times its original volume. Everbuild EVBEVFIRE is gun operated and is ideal for filling:- Gaps around pipe entries through fire rated walls, to provide a fire rated seal around window and door frames, electrical wire chasing prior to plastering, where a fire rating is required, deep joints prior to applying sealant or plaster also irregular gaps in stone, brick, concrete or plaster. Everbuild EVBEVFIRE is ideal for fixing:- door frames, timber structures, windowsills and thresholds and window frames. Also for insulating:- behind cladding to exterior walls, behind sofit and barge boards and even in automotive applications. 750ml

£ 16.98

Fire Foam B1 Gun Grade Aerosol 750ml

The Everbuild Fire Foam B1 Gun Grade is a quick-setting fire rated, one part polyurethane foam, and expands on application to yield up to 50 times the can contents. Fire rated up to 4 hours in certain joint configurations.For use with an Everbuild Professional Foam Gun, once cured the foam can be cut, sawn or plastered over after only one hour.It will fill irregular and broad gaps where most conventional fillers would fail, and possesses insulating, and sound deadening properties.This Fire Foam meets the stringent requirements of DIN 4102 Part 1 for Construction Materials, Class B1 and BS 476 Part 20. Specification: Size: 750ml.

£ 16.98

Dual Purpose Foam Cleaner 500ml

The Everbuild EVBGFSC5 dual purpose foam cleaner is used to remove wet / uncured foam from brick, PVCu, plaster etc. This EVBGFSC5 simply attaches to Everbuild gun foam applicator for purging through, also includes spray nozzle for use without applicator to remove wet foam from outside of the gun and from most building substrates. Easy to use with some simple steps: Pull the trigger on the gun to release the solvent into the gun barrel and discharge the solvent into a suitable container for disposal. Only stop discharging the cleaner when the solution being ejected from the gun is completely clear. Leave the gun foam cleanse attached to the gun for 5 minutes to allow the solvent in the gun to work on the residues inside. Pull the trigger once again until only clear solvent emerges. Leave for a further 5 minutes and repeat this process 2 or 3 times until the gun is completely clear. 500ml.

£ 10.18